![]()
16075 Highway 13 S., Prior Lake, Minnesota 55372 Phone: (952) 440-8778 or FAX (952) 440-8776

3/4-Ton Carryall Battery Box Hinge
Never before available! MWM has custom-made these to exact OEM dimensions.
Others have sold on Ebay recently for over $300.00.
Now you can have one just like the original for $90.00. Satisfaction
guaranteed.

Dodge WC 55 37mm Ammo Box Set
We reproduced a small production run of these never-before-available boxes.
Very precise construction. Sold as a set only.
$1200.00

Lower Radiator Pipe and Hose Set
Replace that always-rusted lower radiator pipe with a fresh MWM reproduction.
Can be used for all WWII Dodges. We also have the correct readiator hoses
in stock.
These look like the original WWII wrapped style material, not some cheap
looking replacement.
Pipe - $15.00
Hose Set - $22.00
Hose Clamps - $3.00 ea.

Heat Riser Kit
Heat riser repair kit for all Dodge 230 exhaust manifolds.
Includes shaft, bushings, butterfly and retainer stud.
$38.00

Command Car Top Bow Main Pivot Bolt
We finally found an original sample to re-make them for you.
Replace that threaded bolt with the correct shoulder bolt.
$5.50 each

Dodge Air Horn Gasket
This gasket goes between the air cleaner adaptor and the air horn on all
WC & M37 series trucks.
$4.00 each

WC54 Rear Step
New, accurate reproduction by Midwest Military.
Correct in all details.
$375.00


Winch Bumper Kit
MWM now offers a complete kit for your winch model WC or Civilian Power
Wagon.
Also available, lower gussets for your non-winch model. Sold in a kit, or
individually.
Kit includes two bumpers and four gussets for $300.00. Gussets separately
- $25.00 each.

1/2 Ton Winch Brackets
USA-made, MWM repro winch mounting brackets for the 1/2 Ton Dodges.
Correct in every way. Paint and install.
$75.00 each.

WC Dodge 1/2 Ton Winch Bumper Set
Get these accurately fitting bumpers for your 1/2 Ton.
We also have the non-winch bumper in stock.
Need gussets? Just ask when ordering your bumpers.
Winch Bumper Set - $90.00/set.
Non-Winch - $100.00.

1/2- and 3/4-Ton Command Car Top Bows
Production is complete! These are exact to the originals with the correct
castings and stamped steel header panel.
We only produced a limited amount. After they are gone we will not be making
more for a few years.
Order yours now. I know it's a big investment but you will NOT be disappointed!
Need individual parts to fix your broken set? Call us.
1/2 & 3/4 Ton Sets - $1500.00


Command Car Top Bow Handle Wheels
3/4-T and 1/2-T top bows require 2 of these hand wheels to secure the middle
swivel point.
MWM re-cast these to aid in your restoration.
$14.00 each.

Lower Fender Support
These are always rusted out or bent up. Get a new exact-fit part from us.
Also fits the Civilian Power Wagons.
$24.00 each.
Fender Repair Kit
Fix that rusted fender back to nw with our kit. Includes a patch panel to
weld in, outer gusset plate, inner support bracket and rivets to re-attach.
Patch panel and gusset plate are pre-formed to match the curve of the fender.
Correct for all 3/4 Ton, 1-1/2 Ton WC's and Civilian Power Wagons.
$45.00/kit.

Dodge Floor Repair Panel
Need a replacement panel for your M37, Civilian Power Wagon, or WC Dodge?
We can custom make any size panel with any pattern diamond stamping. This
one has the Dodge pattern.
This panel is $18.00. Inexpensive to accurately repair your truck.
Prices vary depending on pattern and size. Call for details.

3/4 Ton WC Dodge Floor Plates
New MWM reproduction floor plates for all
3/4 T, 1-1/2 Ton WC Dodges and Civilian Power Wagons.
Top quality. Exact fit.$175.00/set.

Dodge Floor Pan Screws
We just had these custom made. Produced from an NOS sample.
Dress up your restoration with these screws.
Correct for 3/4 & 1-1/2 Ton WC Dodges, and Civilian Power Wagons.
$1.50 each.

Bed Floor Strips
We just finished the tooling to produce an original size and style bed
strip.
These strips take the large head bolt instead of a standard carriage bolt.
Available for all 1/2, 3/4, & 1-1/2 Ton and civilian Dodge trucks. Bed
side angle strips also available.
1/2 & 3/4 Ton - $19.50 each
1-1/2 Ton - $22.50 each.

Dodge Floor Hat Channel
We now stock the correct gauge and size hat channel to aid in
your restoration. Sold by the foot. 5' sections are standard.
$8.00/ft.

WC 1/2-Ton Cargo Box Subframe Kit
All the brackets and wood below the floor - $330.00
Floor kit also available with metal strips and hardware - $425.00



Cargo Box Corners
Do you have rusted or damaged corners on your WC weapons carrier? If so,
we can supply you with an accurately made reproduction. We do require your
old dimples to weld into the new structure, so if you don't have them, we
can't make them right. We can make either front or rear corners for your
box, so don't give up on that rusted ol' truck just yet. Call for details
and pricing. These were just made for another customer's truck. One set
for a 3/4 ton and the other was for a WC 62.
WC Dodge Rear Crossmember
Accurately made by MWM for all 3/4 T & 1-1/2 T Cargo boxes. This
part has never been available before. Replace your bent, broken pieces with
one that is like an OEM.
$90.00

Cargo Box Floor Supports
These are the two middle supports for the open cab 3/4 T & 1-1/2
T Cargo Box floors. EXACT FIT!
Replace your rusted, beat-up pieces with the new replacement made by MWM.
Sold separately at $40.00 - Short
$48.00 - Long

Cargo Box Extension Panels
Correct front bed panels for the 1/2 ton Dodge cargo box.
Used on all open and closed cab express body trucks. Left and right sides
available.
Only one side shown here.
Small panel - $28.00
Larger Panel - $37.50

Cargo Box Spacers
We had these reproduced to the correct size.
Two thick and four thinner ones required per truck. Correct fo M37 and most
other Dodge trucks.
$28.00/set of six.

Dodge Body Mount Pads
Correct for WC series Dodges and will interchange to the M37.
We added the missing cargo box pad for a more complete WC set.
WC Cargo Set - $44.00
M37 Cargo Set - $35.00
Cab Mount Pds - $2.50 each

WC Dodge Wingnut
Here is another MWM product that is not available anywhere else.
This is the correct sheetmetal wingnut for the lazyback arms on all mid-
and late-series open cab Dodges.
Proudly produced by MWM in our shop, not overseas.
$9.00 each.